Sunday, December 11, 2011

!: MAAX Water pump

MAAX Water Pumpset, for more details www.maaxindia.com, +91 9884100041 With our advanced R&D activities, we are able to manufacture Water Pump-set with DIESEL & PETROL ENGINE, which is widely used for various household and farming purposes. These products spares are sourced from the trusted and certified vendors under the strict supervision of our experienced professionals to ensure that these products are flawless and comply with the industry quality standards. Available in varied specifications, we are able to fulfill the individual requirements of our esteemed clients. In addition, we also offer these products at affordable prices.

MAAX Water pump

Projector Lamp Sharp Tips Wiki Fill Rite Fuel Pumps Get It Now

Tuesday, December 6, 2011

!: Sump Pump Submersible Review

When you have residential or commercial wastewater issues, you can count on Zoeller Pumps to deliver the very best solutions-our commitment to top quality offers you years of service and durability. Pls read more info for products details as bellow: No:1, Zoeller M53 Mighty-mate Submersible Sump Pump, 1/3 Hp www.amazon.com No:2, Reliance Controls THP205 Sump Pump Alarm and Flood Alert www.amazon.com N0:3, 24-Foot Sump Discharge Hose Kit with Clamps www.amazon.com

Friday, November 25, 2011

Installing a Sump Pump Made Easy

!: Installing a Sump Pump Made Easy

One of the most difficult parts about owning a sump pump is actually putting it into place. After that, they really require no thought and they will continue to work, sometimes for years in the background. Fortunately, installing a sump pump is not all that difficult, particularly if the sump hole is already in place.

There are two different types of sump pumps that you may need to install, the pedestal variety and the submersible variety. Either of these will really work and it depends on your own personal preference as to which one you're going to use. If you have the submersible variety, installing a sump pump is only a matter of removing the old one and then putting the new one in its place. The only thing that you're really going to need to worry about is making sure that the pump is properly connected to the drain line, otherwise it will simply pump water back into the sump hole.

Installing a pedestal pump may be a little bit more difficult but many people prefer this variety because it is easily adjusted. After removing the old pump from the sump, place the new one in position and make sure to connect the pump with the drain line properly. You are then going to need to adjust the stops on the float bar so that the pump will trigger on and off at the proper times. Make sure that it comes on well before the water reaches the top of the sump hole and goes off in plenty of time so the pump does not run continually.

Installing a Sump Pump Made Easy

Graco Pack N Play Replacement Parts Sale

Tuesday, November 22, 2011

Irrigation Pumps - Different Types For Different Purposes

!: Irrigation Pumps - Different Types For Different Purposes

There are several different kinds of irrigation pumps to choose from. Centrifugal pumps are common type, as are submersible pumps. They are called submersible because they are put completely underwater. These are the types of pumps most commonly found in wells as they are cylindrical in shape. Submersible pumps can be used in lakes as well. There is no need to prime them. These pumps push water and sometimes require special sleeves. The sleeve acts as a coolant by forcing incoming water to flow over the motor.

Then, there are turbine and jet pumps. These pumps are also placed underwater; however, the shaft and motor are above water. Turbine pumps are multiple stage pumps and are very efficient. This is a suction pump. A jet pump is similar except it forces water into the intake to lift water back out.

A booster pump is basically what it is says. It boosts the pressure needed to move water. If you have a sprinkler system that does not have enough pressure to move the water, a booster pump will increase the pressure so the system will work.

Used in lakes and streams is the floating pump. A floating pump is the same as a submersible pump and has the same uses. The main difference is that a floating pump is attached to the bottom of a float.

Pump Performance: The flow and pressure created by the pump determines the pumps performance. The flow and pressure will determine if the pump is right for your project needs. Just remember, increased flow means less pressure. Read the manufacturer's label.

Plan it out: Do not just run out and get a pump. Get a general idea of how the project will be placed. It would also be a good idea to draw up a design of your irrigation system. This will save you money and time.

Irrigation Pumps - Different Types For Different Purposes

Britax Boulevard Onyx Fast Help Thermador Stoves Purchasing Coach Large Totes

Sunday, November 6, 2011

Wayne Water Systems VIP50 1/2 HP 2,500 GPH Submersible Utility Water Pump

!: Prices Wayne Water Systems VIP50 1/2 HP 2,500 GPH Submersible Utility Water Pump for sale

Brand : Wayne | Rate :

| Price : $72.72
Post Date : Nov 06, 2011 13:51:04 | Usually ships in 24 hours

Wayne Water Systems VIP50 1/2 HP 2,500 GPH Submersible Utility Water Pump

This unique Wayne utility pump passes 1/2in. solids such as leaves, pebbles, and other debris without clogging. 1 1/4in. discharge is adaptable to garden hose thread with rotating adapter (included). HP: 1/2, Flow (GPH): 2,500, Volts: 115, Max. Total Head (ft.): 15, Suction Type: Bottom, Discharge Port (in.): 1 1/4, Pump Housing: Glass reinforced thermoplastic, Volute: Glass reinforced thermoplastic, Impeller Shaft: Glass reinforced thermoplastic, Solid Handling (in.): 1/2, Power Cord (ft.): 8, Thermal Overload Protection: Yes, Dimensions L x W x H (in.): 6 3/4 x 6 3/4 x 10

More Specification..!!

Lowest Price Lawn Mowers Electric Cordless

Saturday, October 29, 2011

Finding the Best Pond Pumps

!: Finding the Best Pond Pumps

Having a backyard pond is a great way to showcase a home's landscaping. It adds character and fun to a normally wide open space. The pond pump is an essential device when one wants to add moving water to their pond. There are many different styles and types of pond pumps, so it is easy to get confused on how to find the pump that works best for an individuals situation.

Understanding the essential keys about pond pumps is important in finding the best pond pump. Pumps are categorized by the amount of water they pump. This is based on the gallons of water a pump can move in an hour. It also must pump this amount at least one foot or higher for the same amount of time. Pump manufacturers provide easy to use charts that explain each pump and how much water they move. The best pond pump for a certain pond is chosen based upon how much water is in the pond. The water should be turned at least one turn every hour. So essentially a pond with 200 gallons of water needs a 200 gallon per hour pump. That seems too simple, and it is because there are other factors to consider. Anything that could reduce the flow of water such as waterfalls or filters have to be considered. To avoid this issue a person should buy a larger pump than they figured based solely upon the water amount.

The next step in choosing a pump is deciding between submersible and external pumps. Submersible pumps are located in the pond, while external ponds are outside the pond. Submersible pumps are usually favored because they have many great features. They do not produce noise, can be used to drain the pond and are less expensive to use than external pumps. They do, however, pose problems that are not common in external pumps. Submersible pumps often need seals replaced as they wear out easy with the constant water exposure, broken seals can cause a release of gas that can harm pond fish and they cost more to buy.

Pond pumps are a must for a clean and beautiful pond. Finding the best pond pumps can be tricky. With a little knowledge and use of manufactures recommendations the best pump can be found. Pond pumps provide for a well kept and striking pond.

Finding the Best Pond Pumps

Tips High Pressure Nozzle

Saturday, October 22, 2011

Automatic Starter for Submersible Pump

!: Automatic Starter for Submersible Pump

Normally in all single phase submersible pump we have to press start switch for two second to switch on the pump. and this is so problematic, every time when you switch on pump you have to press this switch, so this the solution i just made monostable circuit which is only on for two second when you switch on then automatically it will switch off, so now i don't have to press this switch every time, circuit will take care about this.. web: www.arshadpthan.com blog: ars2k6.blogspot.com

Automatic Starter for Submersible Pump

Bunk Beds Atlanta Binoculars 25x100 Buy Online !: Xxr Wheels - Lowest Prices Guaranteed

Wednesday, October 19, 2011

Little Giant 5-ASP-LL Water Wizard Submersible Pump

!: Wholesale Little Giant 5-ASP-LL Water Wizard Submersible Pump clearance sale

Rate :

| Price : $121.95 | Post Date : Oct 20, 2011 04:31:03
Usually ships in 24 hours

Little Giant 5-ASP-LL (505350) Submersible Utility Pump / Sump Pump w/ Low-Level Piggyback Diaphragm Switch and oil-filled motor. The 505350 model Pumps down to 1/8" in "manual" mode operation and has a low-level pressure diaphragm which allows the pump to switch with "on" levels at 2" to 3" and "off" ranges at .5" to 1.5" in "automatic" mode. These 5-ASP-LL Little Giant Pumps has a 1" FNPT discharge, as optional regular garden hose adapter, screened inlet and 18ft power cord. Little Giant Utility Pumps 5-ASP-LL Series utility pumps have an epoxy coated cast aluminum housing. For use in commercial, industrial and home applications where liquid must be transferred or recirculated. Specs: * Model Number: 5-ASP-LL; * Horsepower: 1/6; * Max. Flow: 1200 GPH @ 1' of Head; * Cord Length: 18'; * Switch: Automatic, Diaphragm type; * Shut Off: 26.3' ft of head; * Voltage: 115V; * Hertz: 60 Hz; * Amps: 5; * Watts: 380; * Weight: 10.25 lbs.; * Height: 7.75"; * Widht: 4.31"; * Length: 7.7"; * Certification: UL/CSA;

Buying Safe Mouse Traps Low Price Puppet Secrets Hercules Dj Control E2

Monday, October 17, 2011

Submersible Well Pumps - The Basics

!: Submersible Well Pumps - The Basics

If you have a deep water well or are thinking of installing one, that well will probably need a submersible pump. As the name implies, this type of pump is submerged, within the well shaft and sits at or near the bottom of the well. For more shallow wells, an external well pump, that pulls the water out of the well, works fine. But for a deep well, the submersible pump, which pushes the water to the surface is much more efficient.

It is important that the pump be sized correctly for the depth of the well, the pressure you want to maintain, the flow rate you want, and the diameter of your home supply lines (e.g. 2 or 3 inch). They are rated in horsepower, common sizes are 1/2 hp, 1/3 hp, 3/4 hp and 2 hp. It is best to check with a professional plumber or at least your local guy or gal at Home Depot. They can also show you the different models and manufacturers, such as Flotec, Gould, Little Giant and Simer.

If your well is very deep, just the cost of pulling the pump out can be very high, maybe requiring a professional well driller equipment. For this reason, you must be very sure that you know what you are doing. Take your time, read and follow the installation instructions. You don't want to pull it out and do it again. In addition, whenever you are mixing water and electricity, you need to be careful. This is one of those jobs that you really need to consider to leaving to the pros.

Submersible Well Pumps - The Basics

Hurricane Lamps Answer Best Power Washers Interview Kids Guitar Electric

Monday, April 18, 2011

Ponds - The Basics

!: Ponds - The Basics

We all know that a pond is a wonderful thing to have in any garden. If you are building one from scratch then it can be quite daunting, sometimes it's hard to know where to start. So lets take a look at the basics.

The first thing to do is decree what size pond will fit in your organery favorably and exactly where you want to put it, there are no right or wrong places ordinarily as all gardens are different. The main thing to make sure is that you don't put it directly under a tree that may poison the water. So if you have any trees then recognize them first and make sure they will not harm the water or the fish that are in it.

Once you know the location, then it is best to mark out the basic shape with a rope, this way you can get the feel of how your pond will look and you can play colse to with the size and shape. There is more leisure to make your own shape if you are going to use a liner instead of a preformed. But the more straightforward the shape the easier the liner will be to lay.

Before you start to dig, you will need to think about the provide of water and electricity as the closer they are the easier it is for all the ancillaries needed, like your filter and pump, skimmer and fountain, waterfall and lights. Although you may not need all of these things, you will need the pump and filter. So the closer the galvanic provide the better.

Once you have taken the time to plan all of this you can then start to dig, being rigorous of what may be beneath the ground, like cables or drainage pipes. When you have your desired shape it will be time to lay the liner, it is preferable to use an underlay so as to protect the liner. When your liner is in place you can start to fill with water and set up your pump and filter.

The water should be left for a while before you add plants and then once the plants are added and the pump and filter are settled in, again leave the water for a while and test the water with a water testing kit. You can checkout what fish you want to add if you haven't already, then when the water is settled and passed the test you can think about adding your fish.

I don't think I have ever met whatever that regrets building a pond in their garden, they are a wonderful thing and as long as you enunciate them will get good with time. So if you are mental of adding one to your organery then don't hesitate, just make sure you plan right.

Ponds - The Basics

!: Tips Viewsonic Projector Lamp !: Yamaha P120 Right Now !: Hint La Weight Loss Diet Plan Free

Saturday, March 26, 2011

Yookidoo Stack 'N' Stream Tub Fountain

!: Shop For Yookidoo Stack 'N' Stream Tub Fountain Free Shipping

Brand : Yookidoo | Rate :

| Price : $19.20
Post Date : Mar 26, 2011 15:16:17 | Usually ships in 1-2 business days

Magical fountain for bath time play
As boats and characters are stacked up on the base, water flows through each one and out the top
Change the figures for different effects
Easy for children to handle by themselves
Great for babies and toddlers

!: G2 Gatorade Coupons !: Popular Science Order Now !: Comparison Oakley Flak Backpack

Friday, March 18, 2011

Submersible Well Pump How to Replace

!: Submersible Well Pump How to Replace

[if ]

[endif]

Replacing a submersible well pump is not a complex task and relatively simple if you understand the basics about a well ideas - like the placement of the pump, how the submersible pump operates and how it is installed in a well casing. An developed do it yourselfer with knowledge of electrical wiring and some basic plumbing skills is probably capable of replacing a submersible irrigation pump. This is not a step by step factory guide but rather an summary for a general comprehension to rate either to do it yourself or hire a contractor. The savings on the cost of labor, if you do it yourself, will be about 50 - 60% of the total price of a contractor doing the job. The first factor in choosing either to attempt doing it yourself is how deep the well is and do you have a large enough lay down area to layout the pipe in your yard once you start pulling it out of the casing. If your well is 50' to 150' deep, I would propose doing it yourself if you are physically capable to continuously lift and pull about 40 to 70 pounds of weight and hold it in place for while the complete dismissal of pump to keep from dropping it back into the well. To do this you will need at least one other person to help you pull out the pump and guide the dismissal pipe away from the well as you are lifting it out.

The well casing in made of steel, iron or Pvc pipe usually 3"or 4" inside diameter and this acts as a sleeve in which the pump housing, dismissal pipe and wiring go down to reach the water level within this pipe casing. Attached to the submersible pump is the dismissal pipe, usually 1" to 1- ¼" flexible poly pipe and the electrical wiring which also runs into this casing to the depth of submersible pump in the well. The deeper the well, the heavier and more difficult it is to lift out. The weight of the pump assembly may require some rigging above the well casing to help lift and hold the pump assembly in place so it doesn't slip and drop back down into the well casing as you are pulling it out. Once you start pulling up of the pump you must continue the motion until it is fully out of the casing. If you are doing this manually attach a rope beforehand to the top end of well cap so the other person can easier hold on to it and tie it off to something - a tree or fence, in in the middle of lifts if you need to take a break and stop lifting.

If you decide to replace the well pump yourself, here are some tips to remember. decide that the pump motor is bad by checking circuit breakers, switches and check that power is at the well head. If power is on at well head it is a good sign that the pump is broke. Turn off the power at the breaker panel, tag and lock it out for protection before you start exposing the well head. Clear the area nearby the well head, approx 6' to 8' diameter, of shrubs and plants so you have enough room to expose the pump outlet and electrical connections. Disconnect the dismissal pipe and undo the wiring at the junction box near the top of the well. Loosen the bolts on top of the casing cover, this is a squeeze type of cover with a thick rubber ring that expands as tightened and contracts as loosened against the casing interior. Once loose, try to lift the cover, as you lift you will be getting an idea of how heavy the whole assembly is of which you have to lift out of the well.

Now you are ready to lift the pump. Rubber gloves, protective clothing or coveralls should be worn as the pump piping may have an iron and silt residue on the covering and can be quite a messy job. Fasten a pull rope nearby the top of the well head for the other person to hold on and tie off if needed. Some wells may have a leader rope or cable already attached from original factory instead of relying on the dismissal hose clamps and connection. The person who will do the actual pulling should stand directly above the well to lift the dismissal piping level out of the casing and the other person should stay with the top end of well cap and guide it to where you lay it down as you pull. Make sure that the person guiding the end has a good grip on the end before you issue to get an additional one grip. Continue until pump assembly is fully out of the casing and wash off the entire pump end so you read the specification tag of the pump.

Collect the data from the old pump - brand, model, Hp, voltage, phase, 110/220, rpm, 2 or 3 wire configuration, continuous duty and the pumps outlet size and dismissal pipe size. Most residential submersible pumps are either 2 wire or 3 wire configuration. The 2 wire type has 2 - 110v wires along with a Case ground to pump housing. The 2 wire pump needs no controls. If it is a 3 wire pump you should replace the controls also.

Most submersible pump are two piece units bolted together to be one assembly and consists of the motor and the pump. You can just replace the motor or pump if you choose, but I would highly propose that you replace the whole assembly. After you have identified what type and size pump you have you may want to decide to upgrade your ideas with a higher volume pump of keep the same configuration. For upgrading, you should experience a victualer or well contractor for recommendations to be compatible with your needs and piping sizes to which your pump feeds.

Installing the new pump assembly. Make an itemized list of new parts, controls, fittings or wiring as needed. If the existing wiring and flex pipe are in good condition there is no need to replace them. To setup the new pump you will have to splice the electric wires together in a waterproof connection. Consult an electrician or well contractor to specify the power wire splice connector type and technique thorough for well applications. Join together the pipe fittings and pipe clamps as directed in the manufacturer's instructions. Tape the power wires about every 2' for the entire length to the flex pipe for ease in reinstallation of pump into casing. Turn the power to the pump on momentarily to check if it is working before inserting assembly into well. Turn the power breaker off and prepare to insert the pump back into the well again using 2 citizen - one at the well occasion lowering and feeding the pump down and the other person at the well head cover feeding the slack to you and to help hold back to forestall the pump from dropping speedily down the casing.